Parts & Accessories

We designed Teravail tubeless tape for no-hassle installation. Its slight stretch allows the tape to easily conform to your rims. The translucent material shows you exactly where the tape makes contact. It's tacky enough to prevent shifting but easy to pull up if needed, and it won't leave residue on your rims. - Teravail Tubeless Tape comes in a variety of widths to fit almost any rim. - Teravail Tubeless Tape is available in a variety of widths and roll lengths. - Ten-meter length is enough for a single layer on approximately four wheels

The Problem Solvers Axle Nut is perfect for wheels with solid axles (also called bolt-on axles). This quality nut is made of durable chrome-plated steel and features a built-in integrated rotating washer to hold tight.

The Wolf Tooth Rear Axle uses a captive steel washer under the head to reduce friction on the dropout face. This protects your expensive frame, transfers more of the tightening torque to clamping load for a stiffer interface and prevents the axle from sticking or galling when you want to remove it. - Made in Minnesota to aerospace standards

Our Trainer Axle is designed to adapt your thru-axle equipped bike to on-wheel trainers, such as a 1up, Blackburn, Cyclops, Kinetic, Tacx, Wahoo, and many others. Our goal is to fit the thru-axle to your bike perfectly to minimize spacers and extra parts, providing a clean, high-performance axle for your bike. Train, warm up, and be race ready and fit for the season. - When it’s time for your race or time to head outside, simply remove your bike from the trainer, remove the drive side axle end and go. Our axle is suitable for use on or off the trainer, indoors or out. - The axle shaft and axle ends are precision CNC-machined from 7075 aluminum and hard-anodized for rugged durability. - No special tools required. Design allows for installation or wheel removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world. Important: Before you order, make sure your specific trainer will accommodate the width of your modern thru-axle-equipped bike. Measure your trainer at the widest setting and measure the outside width of your bike frame. Our the trainer axle ends will extend past your frame on each side.

Make your WTB rims air tight and ready for tubeless use with WTB's TCS Rim Tape. This tape covers the spoke holes and can be used as a lightweight rim tape in any rim. Available in 11-meter (covers 5 rims) and 55-meter rolls (covers 27 rims).

Secure - Prevents theft instead of standard 9 mm quick-release skewers Quick Assembly - Use proprietary key on frame dropout Construction - Stainless springs with chromoly axle

- Lowest resistance hybrid ceramic (ceramic balls and steel cages) available - Measurable wattage savings between 1.5 and 9 watts per bearing set, depending on the level and condition of your existing bearings - Kits include Freehub body with CeramicSpeed

Wheel Freehub Kit—XD Driver Body Kit—Zipp ZM2 - Compatible With: WH-MOTO-30-B1

Shimano, FH-M828/788/678/648, Freehub body, Y3TH98050

Shimano Dura-Ace 9000 Hub Quick Release Skewer. - Axle Type: Standard QR

Keeping contamination out of your internally geared hub is critical to its function and longevity. Sometimes, the oil port bolt comes loose and it's easy to lose, even if you've just taken it out to oil your hub. Keep a spare or two so your hub stays clean inside and it'll last you many, many miles.

Freehub bodies for Zipp Cognition hubs.

Purchase our Kid Trailer axle for your bike. and share your stoke for cycling with your kids. Simplify your life by allowing quick and secure attachment of your trailer to your best and favorite bike. Enjoy the adventure. Robert Axles for Kid Trailers are designed specifically to fit your 12mm thru-axle bike and allow attachment of any hitch-mounted trailer. These fit any trailer that has two wheels and a single point of attachment to the axle. This includes all the two-wheeled child, pet, and cargo trailers such as Thule, Chariot, Burley, Instep, Carry Freedom, and many more. - This axle is specifically designed to fit the 142/148 hub standard Surly MDS or Gnot Boost bikes. - The derailleur end of our axle is internally threaded and will use the bolt from your stock Surly axle. The disc brake side of our axle has an engineered mount for your trailer hitch. That mount has been permanently attached to the axle. - The axle shaft and axle end are precision CNC-machined. - The axle shaft is 7075 aluminum and hard black-anodized for rugged durability. - The stainless steel axle end allows for mounting of the hitch provided with your trailer. The threads are M10x1 (metric). - Hardware for attachment of the hitch is included; the hitch, itself, is not. - No special tools required. Design allows for wheel installation and removal using your standard 5mm hex wrench. - Designed, built, and quality tested in the USA. Proven around the world.

Wheels Mfg axles are made from aircraft quality 4130 alloy steel, made specifically for Wheels Mfg. It’s heat-treated to increase strength without making the axle brittle. Rolled threads make for easy assembly of cones & locknuts. - Fits many Shimano / Japanese rear hubs with 135mm spacing - Type: Hollow Axle - Threads: 10mm x 1 - Diameter: 10mm - Length: 146mm - 1 axle per bag

This is our Excellent Adventure Thru-Axle. It upgrades your bike's rear end for hauling cargo trailers, should you feel like taking Rufus along on your errands. Extensive product testing with our Bill and Ted Trailers provided an "awesome experience," but time travel remains a risky endeavor. Designed for use with slotted horizontal or vertical single-position dropouts, the Excellent Adventure Axle is compatible only with 12 x 148mm hubs. Compatible Surly models include Skid Loader, our compact electric cargo bike, as well as Karate Monkey, Krampus, Grappler, Ogre, Lowside, ECR, and Troll. Once again, the 12 x 148mm hub requirement cannot be overstated. Visit your local Surly dealer to discuss other scenarios you may have in mind. - 12 x 148mm hub compatibility only - Designed for use only with Surly's Bill and Ted Trailers - Works with slotted horizontal or vertical single-position dropouts

Rear axle conversion kits convert your hub to fit a new axle measurement or for a new group set. All DT Swiss hubs can be converted.

Small component with a large impact. A poorly constructed or unsuitable tyre rim tape can be the cause of many punctures. It is especially important with hollow section rims to use a pressure-resistant rim band which covers the entire rim. The fabric-reinforced Continental Easy Tape rim protector is designed for use under high air pressure conditions. The various widths enable a perfect fit for all standard rims. The high pressure design for racing cyclists withstands up to 220 psi, without becoming deformed. The flat construction type also significantly eases the job of tyre fitting.

Ratchet freehub bodies have a gloss finish and don't have a seal, as this is fixed on the hub shell. The Ratchet System was the first of this type for DT Swiss; used in the mid-range products like the 350 hubs. - End Cap Included

After years of mountain biking with thru-axles with bulky handles that seemed to strike every trailside obstacle, we needed a better option. Our Lightning Bolt-On thru axles offer a high-quality, simple, lightweight alternative to that bulky handle. Available in a range of sizes that fit both front and rear wheels on all types of thru-axle-equipped bikes. - Lightning is Better—Our front and rear Lightning Bolt-On axles offer a stronger, more durable, lower profile, and lighter weight option to replace your stock thru-axles. - Low Profile—No more bulky handles to strike trail obstacles. Aerodynamic design. - Light Weight—Our axles are internally bored to remove unnecessary material without compromising strength. - Easy to install—Our matching front and rear Lightning Bolt-On Axles require only a standard 6mm hex wrench for easy installation and removal. - Better Tolerances—Manufactured in the USA to the tightest tolerances using aerospace materials and CNC manufacturing. No longer will your axle loosen while riding.

WTB's TCS AL valves are aluminum to shed grams, and come in catchy anodized red, black, or blue. A stepped lock nut adds compatibility among various rim drillings, a smooth pump interface makes adding air easy, and a removable core makes setting beads and injecting sealant a cinch. - Presta - 46mm

Convert your ISO, ISO B, or ISO Superboost DH rear hub to a Shimano Micro Spline compatible driveshell. The conversion kit is complete with an axle, adjustment clamp, driveshell, and all driveshell internals for a plug-and-play swap. Micro Spline Driveshell Instructions - Compatible with Shimano Micro Spline cassettes; XTR, XT, and SLX - Compatible with ISO 142x12mm, ISO B 148x12mm, and ISO Superboost DH 157x12mm rear hubs.

Match your Beyond Black hubs, spokes and decals (each sold separately) with skewers from Zipp. - Sold in pairs - Stainless steel: 85 grams/set - Titanium: 78 grams/set

SRAM's Quick Releases hold your wheel tightly in place, are built for ease of use and made to last, too. You get a front and rear quick release.

Heavy duty and extra wide PVC rim strips for maximum tube protection.

The Stolen rim strip features 30mm width and 20" diameter. - Material: PVC - Wheel Size: 20" - Rim Strip Width (mm): 30 mm - Adhesive: No

V2 Tubeless valves are stronger, lighter, and even easier to use thanks to the machined aircraft grade 7075 aluminum and Muc-Off's new Tire Insert air ?ow system. The new design features six slots that are machined into the base of the valve stem, allows tubeless sealant ?uid and air to ?ow freely, even when running tubeless tire inserts. - 7075 Machined Aluminum valve stem and cap - Tire Insert air flow system keep air moving freely and compatible with most tire foam inserts - 4mm machined Allen Key slot for easy installation and removal - Includes Valve Core Removal Tool (integrated into spare alloy cap) - Supplied with various rubber bases to optimize fit with multiple rim types

SRAM's X0 conversion caps are the ticket for converting your X0 hubs to a different axle type.

Rear Thru Axle conversion kit for Go-Devil Hubs - Converts QR to 142x12mm thru (axle not included)

Who knew we could make a thru axle disappear? The new Maxle Stealth offers a light, low profile alternative to Maxle Lite. - Hub OLD 20x110 - Length 158mm - Thread Length 10mm - Thread Pitch M20x1.50 - BoXXer C1 (2019+) - 34g lighter than Maxle Lite - Easy installation with a 6mm Allen wrench - Compatible with all 15mm forks

Wheels Manufacturing cones are precision machined to Shimano Ultegra or higher quality standards. This ensures that our cones fit correctly, run smoothly and have a long service life. - Compatible with Shimano Front 9mm x 1 axle - 22mm metal dust seal is pressed on cone - Cone Wrench Size: 13mm - Threads: 9mm x 1 - Cone Diameter: 15.0mm - Dust Seal Diameter: 22mm - Length: 11.4mm - 1 cone per bag COMPATIBLE HUBS: - Shimano Nexave HB-T400 Front - Shimano Deore HB-M510 Front - STX HB-MC32/30 Front - STX Parallax Front